Skip to main content

Not sure which part you need? Start with the buying guide below, or browse all caravan towing accessories.

Caravan Hitch, Coupling or Tow Ball: What’s the Difference?

“Hitch” can refer to several towing components, so it’s worth knowing which part you’re replacing before you buy.

On many tow vehicles, a removable tow ball mount (often called a towbar hitch or tongue) slides into the towbar receiver and is secured with a hitch pin. Other towbar designs have a fixed or directly mounted tongue. The tow ball (or a tow pin for some off road couplings) bolts to the mount, and the coupling on the caravan’s drawbar locks onto it.

PartWhat it doesWhere it fitsWhen to choose it
Caravan couplingConnects the van to the tow ball or pinCaravan drawbarReplacing a worn coupling or switching to an off road coupling
Tow ball and tow ball mount (towbar hitch)Gives the coupling an attachment pointTow vehicle’s towbarNew tow vehicle, correcting ball height or replacing a worn mount
Weight distribution hitchSpring bars spread some tow ball load across the tow vehicle and caravan axlesBetween towbar receiver and drawbarWhen extra weight distribution is needed and the setup is approved for it
Hitch accessoriesLock, secure and check the connectionCoupling, tow ball or receiverSecurity and checking ball weight

How to Choose a Caravan Tow Hitch

Match the ratings

Check the towing capacity of your vehicle and the ratings of your towbar, tow ball mount, tow ball and coupling. Each component must be rated for the load it carries, and your setup must stay within both the lowest applicable towing capacity and the permitted tow ball weight.

Aggregate Trailer Mass (ATM) is the caravan’s maximum fully loaded weight, shown on its compliance plate. Ball weight is the downward load the coupling places on the tow ball. Check both against the vehicle owner’s manual and the ratings marked on the towbar and coupling (WA Department of Transport Safe Towing Guide; SA Government towing regulations).

Ball weight also counts towards the tow vehicle’s Gross Vehicle Mass (GVM). The loaded vehicle and van together must stay within the vehicle’s Gross Combination Mass (GCM), and each axle must stay within its own limit.

As a general guide, WA’s Department of Transport suggests a ball weight of 8 to 10% of ATM, up to the towbar’s limit. The right figure depends on your setup, so follow manufacturers’ limits and use tow ball weight scales to measure rather than guess.

Check the tow height

Level towing means the caravan sits roughly level when hitched and loaded. If the tow vehicle sags at the rear, steering, front braking and headlight aim can all suffer. To compare heights:

  1. Park the loaded van on level ground and level it with the jockey wheel.
  2. Measure from the ground to the coupling.
  3. With the tow vehicle loaded, measure to the equivalent point on the tow ball.

If they don’t match, a towbar hitch with a different drop or rise can close the gap. Only flip a tongue if it’s designed for it, and check its rating in that position.

Match the ball size and coupling

The tow ball must match the coupling, which is marked with its ball size and rating. 50 mm tow balls are the most common for caravans and aren’t rated beyond 3,500 kg.

Also check the hitch shank suits your towbar receiver; similar looking parts aren’t always interchangeable.

On road or off road van?

Off road couplings allow far more articulation than a standard ball coupling. Some, like the Cruisemaster DO35, replace the tow ball with a tow pin on the vehicle. Others, such as the Ark XO off road coupling, fit over a 50 mm tow ball, although Ark specifies a ball that complies with AS 4177.2 and doesn’t have a flat flange. Check what your coupling needs on the vehicle side and that its rating suits your van.

Not sure which hitch suits your van?Contact the Campsmart team with your van’s ATM, coupling type and tow vehicle.

Do You Need a Weight Distribution Hitch?

Once the coupling suits your caravan and tow vehicle, consider whether you need a weight distribution hitch. Not every setup does. One uses tensioned spring bars to redistribute some tow ball load across the tow vehicle and caravan axles, helping level a vehicle that sags at the rear under a heavier ball weight.

It won’t fix an overloaded van, excessive ball weight or an overloaded rear axle, and shouldn’t be used where the vehicle, caravan, towbar, coupling or hitch manufacturer advises against it. Choose a system rated for your ball weight. With an off road coupling, also check the system is compatible and whether it must be disconnected for off road travel. For more detail, read our guide on how to choose the right weight distribution hitch.

Hitch Safety and Fitting Checks

Compatible parts are only half the job. Before towing, check the connection is secure and the hitch is in good condition.

  • Inspect the coupling, tow ball and hitch for cracks, wear and play.
  • Make sure the coupling’s locking mechanism is fully engaged, any secondary lock is in place and the hitch pin’s retaining clip is fitted.
  • Connect the safety chains, then check the electrical and brake connections.
  • Fit hitches in the direction the manufacturer marks; never invert one unless it’s designed for that.
  • Check mounting bolts regularly.
  • Remove the hitch when not towing if it blocks the number plate.

Installing or modifying a towbar affects safety and must meet compliance requirements that vary by state and territory, so professional fitting is recommended.

Caravan Hitch Accessories

With the hitch and coupling sorted, these accessories help with hitching, security and visibility.

Setting up your first van? Browse the new caravan owner collection for more gear to sort out before you hit the road.

Frequently Asked Questions

What is the difference between a caravan hitch, coupling and tow ball?

The coupling is mounted on the caravan’s drawbar and connects to the tow ball or tow pin, depending on the design. “Hitch” usually means that mount, often called a towbar hitch, though some people use it for the coupling or the whole connection. Some off road couplings use a tow pin instead.

What size hitch do I need for my caravan?

Start with the ratings. The tow vehicle, towbar, tow ball mount, tow ball and coupling each have their own rating, and the lowest one sets the limit for your caravan’s ATM and ball weight. Then match the tow ball to the size marked on the coupling, commonly 50 mm, and check the hitch shank suits your receiver.

How high should a caravan hitch be?

High enough that the loaded caravan sits roughly level when hitched. Level the van on flat ground with the jockey wheel, measure from the ground to the coupling, then measure the tow ball height on the loaded tow vehicle. If they don’t match, a towbar hitch with a different drop or rise can close the gap.

Can I use a weight distribution hitch with an off road coupling?

It depends on the coupling. WA’s Safe Towing Guide says high articulation couplings used with weight distribution should only be used on highways. Some manufacturers allow it under set conditions; others advise against load levelling devices off road. Check your coupling’s instructions.

Can I fit a caravan hitch myself?

Inserting a compatible removable hitch into an existing towbar may be straightforward if you follow the manufacturer’s instructions. Installing or modifying the towbar itself affects safety and compliance, so professional fitting is recommended. Campsmart doesn’t provide installation or technical support.

What is a DO35 coupling?

The DO35 is Cruisemaster’s off road coupling. It connects to a tow pin on the tow vehicle’s towbar instead of a tow ball, allowing more articulation on rough ground. Cruisemaster rates the Australian version to 3,500 kg.

Find the Right Hitch for Your Setup

Browse the caravan tow hitch range above, read our buying guides or lodge a product enquiry if you’re unsure. Check ratings and measurements first, as items that have been fitted or used can’t be returned for change of mind.

Footer